The separator for greasy wastewater is suitable for installation in the ground and comes without metallic components in the tank. The collecting tank made of permanently resistant polymer (PE) is equipped with an integrated sludge trap and has a rounded base for fast and clean disposal. Access for cleaning and maintenance work is possible via one or several service access covers. The innovative Shredder-Mix-System with integrated macerating system is responsible for homogenising and circulating the tank contents. Cleaning takes place via an exterior pump which is installed in a separate engineering chamber and can be disconnected from the tank by a shut-off valve. A direct disposal pipe socket is available for odour-neutral manual disposal. 20 year polyethylene warranty.
Variant
Note on installation depth: Installation in the ground, frost-free depth 800 mm
Shut-off valve: yes
Disposal variant: Mix
Shredder-Mix-System: yes
Sludge bucket: no
Nominal size (NS): 1,00
SonicControl: no
Disposal system: Disposal connection
Refill inlet in accordance with DIN 1988: no
Type of disposal: manual cleaning system
Water supply: 1 screw-type valve 1"
Sampling device: Type NBG
Load-bearing capacity (DIN 19901): E2
General characteristics
Material: PE
Standard: EN 1825: 2004
Installation situation: underground installation
Delivery state: Installation-ready (electrical components, connection parts must be connected on site)
Scope of delivery: Storz-B coupling R 2 1/2" for disposal vehicle connection
Dimensions
Net weight: 350 kg
Gross weight: 370 kg
Groundwater resistant from lower edge of base section: 500 mm
Installation depth: 550 - 950 mm
Type of height adjustability: vertically adjustable upper section, can be tilted by 5 degrees
Required access area, length: 1380 mm
Required access area, width: 1220 mm
Required access area, height: 1500 mm
Tank/drain body
Distance pipe bottom outlet to tank bottom: 690 mm
Distance pipe bottom inlet to tank bottom: 795 mm
Outlet nominal size (OD): 110 mm
Outlet nominal size (DN): 100 mm
Inlet nominal size (OD): 110 mm
Inlet nominal size (DN): 100 mm
Connection inlet/outlet sockets: PE-HD pipes in accordance with DIN 19537, PVC-KG pipes in accordance with DIN 19534, PP or AS
Clear width of tank (LW): 1000 mm
Clear width of entry (LW): 600 mm
Coverage features
Type of cover: Cover plate
Cover material: Grey iron
Colour of cover: black
Width of cover: 648 mm
Height of cover: 95 mm
Length of cover: 648 mm
Locking: locked
Load class: B 125 (EN 124)
Tightness: odour-tight and surface water resistant
Wastewater contents
Separator contents: 230 l
Total volume: 370 l
Contents of sludge trap: 140 l
Storage quantity of grease: 70 l
Pumping device
Pump: SPF 260 KE
Number of pumps: 1
Weight, pump: 40 kg
Connection type: Direct connection
Rated current: 6,4 A
Protection class: I
Insulation class: F
Protection class (pump): IP 68 (3m/48h)
Temperature monitoring: integrated
Max. temperature (permanent) of conveyed material: 40 °C
Max. pumping capacity: 65 m³/h
Max. pumping height: 13 m
Speed: 2850 U/min
Power P1: 3,4 kW
Power P2: 2,6 kW
Operating mode: S2 - 30 min.
Type of pump connection cable: H07RN-F 7G 1.5 mm²
Impeller type: Radial impeller with macerating system
Length of mains cable for pump: 5 m
Control
Control unit: yes
Type of fuse required (RCD): 30 mA
Mains frequency: 50 Hz
Operating voltage: 400 V
Connection type: Direct connection
