The separator for greasy wastewater is suitable for free-standing set-up in frost-protected rooms and comes without metallic components in the tank. The collecting tank made of permanently resistant polymer (PE) is equipped with an integrated sludge trap and has a tapered base for fast and clean disposal. Two odour-tight covers with quick-release closures make easy access possible for cleaning and maintenance work. The innovative Shredder-Mix-System with integrated macerating system is responsible for homogenising and circulating the tank contents. Cleaning and odour-neutral disposal takes place via an exterior pump with 2-way valve and change lever which can be disconnected from the tank by a shut-off valve. After disposal, a maximum of 3 litres residual sludge volume is left in the tank. Manual control is carried out by a user-friendly control unit that can be integrated into the building management system through a potential-free contact. 20 year polyethylene warranty.
Variant
Shut-off valve: yes
Shredder-Mix-System: yes
Sludge bucket: yes
Nominal size (NS): 7
Disposal system: Disposal pump
Refill inlet in accordance with DIN 1988: yes
Type of disposal: manual disposal and cleaning system
Water supply: 1 screw-type valve 1"
General characteristics
Material: Polymer
Installation situation: free-standing installation
Delivery state: Installation-ready (electrical components, connection parts must be connected on site)
Scope of delivery: Storz-B coupling R 2 1/2" for disposal vehicle connection
Dimensions
Net weight: 190 kg
Gross weight: 190 kg
Set-up area, length: 1600 mm
Set-up area, width: 1220 mm
Required access area, length: 1850 mm
Required access area, width: 990 mm
Required access area, height: 1560 mm
Tank/drain body
Nominal pressure (PN): 10
Pressure pipe connection (DN): 65
Pressure pipe connection (OD): 75 mm
Distance pipe bottom outlet to tank bottom: 1130 mm
Distance pipe bottom inlet to tank bottom: 1200 mm
Outlet nominal size (OD): 160 mm
Outlet nominal size (DN): 150 mm
Inlet nominal size (OD): 160 mm
Inlet nominal size (DN): 150 mm
Connection inlet/outlet sockets: PE-HD pipes in accordance with DIN 19537, HT pipes in accordance with DIN 19560, PP or AS
Servicing opening: 420 mm
Coverage features
Type of cover: Cover
Cover material: Polymer
Colour of cover: black
Locking: Quick-release closure
Tightness: odour-tight
Wastewater contents
Separator contents: 567 l
Contents of sludge trap: 700 l
Storage quantity of grease: 302 l
Pumping device
Pump: SPF 300 KE
Number of pumps: 1
Weight, pump: 44 kg
Connection type: Direct connection
Rated current: 6,2 A
Length of mains cable for pump: 5 m
Protection class: I
Insulation class: F
Cos phi - power factor: 0,87
Protection class (pump): IP 55
Temperature monitoring: integrated
Max. temperature (permanent) of conveyed material: 40 °C
Max. pumping capacity: 60 m³/h
Max. pumping height: 17 m
Speed: 2850 U/min
Power P1: 3,6 kW
Power P2: 3 kW
Operating mode: S2 - 30 min.
Type of fuse required (electrical protection): Fuse protection through control unit 400 V
Type of pump connection cable: H07RN-F 7G 1.5 mm²
Impeller type: Radial impeller with macerating system
Control
Control unit: yes
Motor protection switch: yes
Type of fuse required (RCD): 30 mA
Protection class control unit: IP 54
Mains frequency: 50 Hz
Operating voltage: 400 V
Connection type: Direct connection
Potential-free contact: yes
GSM interface: no
USB interface: no
Log book function: no
Multi-line display: no
Battery buffering: no
Self-diagnosis system (SDS): yes
Rated current: 6,2 A
